Should shaver sockets get warm?Asked by: Brayan Hills
Score: 4.4/5 (49 votes)
Yes it is ok as long as it's just a bit warm and not red hot. It's just the transformer for the shaver socket according to my electrician. I've had a couple of these cheaper shaver lights & they all seem to get a bit warm. My current one has been installed & warm for a few years with no problems.View full answer
Also, Do shaver sockets get hot?
The transformer runs all of the time, and they do use power even when there is no load attached, hence they generate heat.
Then, Why does my shaver socket hum?. Re: Shaver socket hum
The hum is the transformer core laminations rattling due to the load on the transformer. If the transformer frontplate is not getting excessivly hot then all is well.
Similarly one may ask, Can you plug appliances into shaver socket?
In other words, it's probably fine to use most “shavers only” plugs for most small solid-state electronics, including phone chargers. But you should avoid using them to power laptops, hairdryers, curling irons, or other high-draw devices.
What is special about a shaver socket?
The bathroom shaver socket is mounted in an isolation transformer that cuts it off from the rest of the electrical system. This limits the risk of electrical shock, a concern in the bathroom where lots of water can be present. In addition, the current is very low.
Usually, outlets that read “Shavers Only” means that there is not much electricity running to that outlet – enough for a shaver, and to recharge stuff, but usually anything drawing more electricity will cause the breaker to fail/blow as they are usually running low amps/watts.
Both types of shaver socket-outlet may be either Class I construction (having metal parts required to be earthed) or Class II construction (having no exposed metal parts required to be earthed). ... A shaver socket-outlet with a transformer is called a shaver supply unit.
Or even you didn't forget your phone charger if you travel between UK and Europe you might forget the converter or adapter. If you stay in a hotel you must have seen one of those Shaver-only outlets. ... It's ok to charge your phone with those sockets.
In short, yes it will work but the socket may eventually fail. Not just toothbrushes which often take 24 hours to charge or are designed to be permanently trickle charging but rechargeable shavers too.
All manufacturers and importers are required to ensure that electrical items they supply in the UK are fitted with UK three-pin plugs with the proper fuse. ... Distributors and retailers must not sell any appliances without a correct fused plug fitted.
A Quick Summary On Why Bathroom Mirrors Buzz
Two of the main reasons for humming are vibrating shaving sockets and LED problems. LED problems can include electromagnetic interference and incompatible dimming devices.
Yes you can take your toothbrush with you when travelling. ... Most larger hotels will have a 'shaver socket' in the bathroom that will be suitable for your electric toothbrush.
Why are there no plug sockets in British bathrooms? The reason that there are no plus sockets in bathrooms is simple – having an exposed plug socket can increase the risk of electric shock. Plugs in England generally use 240-volt power, twice the amount found in US plugs which have 120-volts.
There is no need to charge two at the same time. Charge one first then the other. Since shavers only need charging every couple of weeks or so there is ample time to charge not only two but many more over two weeks.
Sockets. Sockets are not allowed in bathrooms or shower rooms (apart from shaver-supply units) unless they can be fitted at least three metres from the bath or shower.
1 Answer. UK shaver sockets are not a lower voltage, but the ones in bathrooms include an isolating transformer and thermal cutout so that neither wire of the shaver has any voltage to earth (so a shock to earth is impossible) and the socket cannot be used for more powerful appliances.
In many older houses and condos, you still can find a “razor only” outlet in the bathroom. These usually have a polished silver plate and only two prongs. They were designed to separate you from the grounded electrical system in your home by limiting the amount of current that could flow in a fault condition.
A shaver socket must only supply one item. If there are two outlets they both must have their own isolated windings. They are type tested and it is not permissible to alter them and although it would seem safer to have the transformer remote from socket it is not allowed.
Shaver sockets are becoming a common feature in bathrooms, whether they are directly installed into the wall, or they come as a feature in a mirrored cabinet. In relation to bathroom zones, shaver socket regulations state that one must be placed at least 3m horizontally from the boundary of zone 1.
In terms of wiring, the cable running form the existing socket circuit to the FCU should be 2.5mm twin and earth and the cable from the FCU to the shaver socket should be 1mm twin and earth.
This shaver & toothbrush Converter plug will let you convert your UK 2 pin adaptor to 3 pin. Just Connect to your wall socket and use it. Easily allows you to charge your electric shavers, toothbrushes and epilator from a standard 3 pin UK socket.
A 2 pin to 3 pin adapter works by allowing a 110-volt item (with the 2-pin plug) to be plugged into the 240-volt outlet (the 3-pin plug socket). Inside the 2 pin to 3 pin adapter, the current flows at the required level. Some appliances have voltage changers inside them that allow them to use the available current.
you need to confirm separation of the transformer in the unit itself, and then segregation of the circuit supporting the shaver from the rest of the circuits of the install. to test the shaver unit before install on the bench, lift off the cover from the terminals( this will be slightly different for each manufacturer) ...
Prong Design: Like standard U.S. grounded plugs, the U.K. wall plug has three prongs. ... Although the built-in fuse adds bulk to the U.K. plug design, it's also safer: In case of an unexpected electrical surge, the fuse simply blows and the electricity shuts off, preventing fires, electrocutions, and other accidents.